Skip to content
Learning Center About Us Contact Us
Outdoor Water Solutions Font`N-Aire Platinum 5HP Carnival Nozzle 3 Phase

Outdoor Water Solutions Font`N-Aire Platinum 5HP Carnival Nozzle 3 Phase

by Outdoor Water Solutions
$8,795.00

Notify me when back in stock

Font`N-Aire Platinum 5HP Carnival Nozzle 3 Phase

The unique configuration of the CENTRIFUGAL PUMP DISPLAY FOUNTAIN is characterized by its center discharge pump design, ensuring a vertical alignment of both the submersible motor shaft and the discharge. This distinctive feature concentrates the entire weight of the fountain at the center of the float. Notably, this design simplifies the installation and removal process, eliminating the necessity for special mounting brackets or hardware.

Furthermore, our centrifugal pump design excels in generating high pressure, enabling the creation of impressive fountain heights and displays. Notably, this is achieved with significantly lower horsepower requirements compared to alternative fountain equipment. It's essential to highlight that this fountain is exclusively designed for aesthetic purposes. While it produces captivating water displays, the volume of water propelled into the air is insufficient to be classified as an aerating device, as per rigorous testing and compliance with Air-O-Lator's standards for oxygen transfer.

Major Components
  • FLOAT – constructed of rugged polyethylene molded plastic with UV inhibitors and filled with non-hygroscopic pressure molded polystyrene foam.
  • POWER DRIVE ASSEMBLY – mounting structure (drive structure assembly), pump/propeller, nozzle, and motor.
  • ELECTRICAL SERVICE CABLE ASSEMBLY – 100’ (minimum) of AWG# 12/4 submersible cable and a submersible quick disconnect connector, which plugs into the fountain.
  • CONTROLS – 24-hour time clock with multiple off/on trippers, a Franklin Electric start and run QD capacitor box, and an inline ELCI ground fault protector with a standard 230 volt, 15 amp plug. All of the components are prewired and mounted on a 16” x 14” plate. Air-O-Lator exclusively uses the Franklin Electric 600M submersible motor on all fountain lines. The water cooled and lubricated motor is specifically designed for lake and pond fountain applications and is environmentally safe.
    • Features
  • No seals or bearings to maintain.
  • High speed, foul resistant propellers or impellers, provide high shear water spraying action. No lazy sprays, bubbles, or slow boil of water.
  • One piece square flotation for stability to minimize any oscillation that can occur with round floats.
  • Watertight, removable, 100’ power cable is standard. Additional cable lengths are available in 50’ increments.
  • ETL listed (ANSI/UL508) control panel with time clock (adjustable in 15-minute increments), and Equipment Leakage Circuit Interrupter (ELCI) (US only).
  • Exclusive Franklin Electric Sand Fighter submersible motor, which implements the use of a silicon carbide mechanical sealing system.
  • 3 year Limited Warranty
  • 5HP – 11? Tall x 35? Width

    • LEAVE A MESSAGE

    Font`N-Aire Platinum 5HP Carnival Nozzle 3 Phase

    The unique configuration of the CENTRIFUGAL PUMP DISPLAY FOUNTAIN is characterized by its center discharge pump design, ensuring a vertical alignment of both the submersible motor shaft and the discharge. This distinctive feature concentrates the entire weight of the fountain at the center of the float. Notably, this design simplifies the installation and removal process, eliminating the necessity for special mounting brackets or hardware.

    Furthermore, our centrifugal pump design excels in generating high pressure, enabling the creation of impressive fountain heights and displays. Notably, this is achieved with significantly lower horsepower requirements compared to alternative fountain equipment. It's essential to highlight that this fountain is exclusively designed for aesthetic purposes. While it produces captivating water displays, the volume of water propelled into the air is insufficient to be classified as an aerating device, as per rigorous testing and compliance with Air-O-Lator's standards for oxygen transfer.

    Major Components
  • FLOAT – constructed of rugged polyethylene molded plastic with UV inhibitors and filled with non-hygroscopic pressure molded polystyrene foam.
  • POWER DRIVE ASSEMBLY – mounting structure (drive structure assembly), pump/propeller, nozzle, and motor.
  • ELECTRICAL SERVICE CABLE ASSEMBLY – 100’ (minimum) of AWG# 12/4 submersible cable and a submersible quick disconnect connector, which plugs into the fountain.
  • CONTROLS – 24-hour time clock with multiple off/on trippers, a Franklin Electric start and run QD capacitor box, and an inline ELCI ground fault protector with a standard 230 volt, 15 amp plug. All of the components are prewired and mounted on a 16” x 14” plate. Air-O-Lator exclusively uses the Franklin Electric 600M submersible motor on all fountain lines. The water cooled and lubricated motor is specifically designed for lake and pond fountain applications and is environmentally safe.
    • Features
  • No seals or bearings to maintain.
  • High speed, foul resistant propellers or impellers, provide high shear water spraying action. No lazy sprays, bubbles, or slow boil of water.
  • One piece square flotation for stability to minimize any oscillation that can occur with round floats.
  • Watertight, removable, 100’ power cable is standard. Additional cable lengths are available in 50’ increments.
  • ETL listed (ANSI/UL508) control panel with time clock (adjustable in 15-minute increments), and Equipment Leakage Circuit Interrupter (ELCI) (US only).
  • Exclusive Franklin Electric Sand Fighter submersible motor, which implements the use of a silicon carbide mechanical sealing system.
  • 3 year Limited Warranty
  • 5HP – 11? Tall x 35? Width

    • LEAVE A MESSAGE