Skip to content

Outdoor Water Solutions Font`N-Aire Platinum 5HP Carnival Nozzle Single Phase

$8,795.00

Notify me when back in stock

Font`N-Aire Platinum 5HP Carnival Nozzle Single Phase

The distinctive design of the CENTRIFUGAL PUMP DISPLAY FOUNTAIN ensures optimal functionality by featuring a center discharge pump. This design guarantees that both the submersible motor shaft and the discharge are maintained in a vertical position. As a result, the entire weight of the fountain is concentrated in the center of the float, streamlining the installation and removal process without the necessity for specialized mounting brackets or hardware.

Moreover, our centrifugal pump design stands out in its ability to generate high pressure, allowing for the creation of impressive fountain heights and displays. Notably, this design achieves such results with significantly lower horsepower requirements compared to other fountain equipment.

It's crucial to emphasize that the primary purpose of this fountain is aesthetic, as the water volume propelled into the air is not substantial enough to qualify as an aerating device according to rigorous standards set by Air-O-Lator. The focus is on creating visually appealing displays without serving as a dedicated oxygen transfer device, as determined through comprehensive testing.

Major Components
  • FLOAT – constructed of rugged polyethylene molded plastic with UV inhibitors and filled with non-hygroscopic pressure molded polystyrene foam.
  • POWER DRIVE ASSEMBLY – mounting structure (drive structure assembly), pump/propeller, nozzle, and motor.
  • ELECTRICAL SERVICE CABLE ASSEMBLY – 100’ (minimum) of AWG# 12/4 submersible cable and a submersible quick disconnect connector, which plugs into the fountain.
  • CONTROLS – 24-hour time clock with multiple off/on trippers, a Franklin Electric start and run QD capacitor box, and an inline ELCI ground fault protector with a standard 230 volt, 15 amp plug. All of the components are prewired and mounted on a 16” x 14” plate. Air-O-Lator exclusively uses the Franklin Electric 600M submersible motor on all fountain lines. The water cooled and lubricated motor is specifically designed for lake and pond fountain applications and is environmentally safe.
  • Features
  • No seals or bearings to maintain.
  • High speed, foul resistant propellers or impellers, provide high shear water spraying action. No lazy sprays, bubbles, or slow boil of water.
  • One piece square flotation for stability to minimize any oscillation that can occur with round floats.
  • Watertight, removable, 100’ power cable is standard. Additional cable lengths are available in 50’ increments.
  • ETL listed (ANSI/UL508) control panel with time clock (adjustable in 15-minute increments), and Equipment Leakage Circuit Interrupter (ELCI) (US only).
  • Exclusive Franklin Electric Sand Fighter submersible motor, which implements the use of a silicon carbide mechanical sealing system.
  • 3 year Limited Warranty
  • 5HP – 11? Tall x 35? Width
  • LEAVE A MESSAGE

    Font`N-Aire Platinum 5HP Carnival Nozzle Single Phase

    The distinctive design of the CENTRIFUGAL PUMP DISPLAY FOUNTAIN ensures optimal functionality by featuring a center discharge pump. This design guarantees that both the submersible motor shaft and the discharge are maintained in a vertical position. As a result, the entire weight of the fountain is concentrated in the center of the float, streamlining the installation and removal process without the necessity for specialized mounting brackets or hardware.

    Moreover, our centrifugal pump design stands out in its ability to generate high pressure, allowing for the creation of impressive fountain heights and displays. Notably, this design achieves such results with significantly lower horsepower requirements compared to other fountain equipment.

    It's crucial to emphasize that the primary purpose of this fountain is aesthetic, as the water volume propelled into the air is not substantial enough to qualify as an aerating device according to rigorous standards set by Air-O-Lator. The focus is on creating visually appealing displays without serving as a dedicated oxygen transfer device, as determined through comprehensive testing.

    Major Components
  • FLOAT – constructed of rugged polyethylene molded plastic with UV inhibitors and filled with non-hygroscopic pressure molded polystyrene foam.
  • POWER DRIVE ASSEMBLY – mounting structure (drive structure assembly), pump/propeller, nozzle, and motor.
  • ELECTRICAL SERVICE CABLE ASSEMBLY – 100’ (minimum) of AWG# 12/4 submersible cable and a submersible quick disconnect connector, which plugs into the fountain.
  • CONTROLS – 24-hour time clock with multiple off/on trippers, a Franklin Electric start and run QD capacitor box, and an inline ELCI ground fault protector with a standard 230 volt, 15 amp plug. All of the components are prewired and mounted on a 16” x 14” plate. Air-O-Lator exclusively uses the Franklin Electric 600M submersible motor on all fountain lines. The water cooled and lubricated motor is specifically designed for lake and pond fountain applications and is environmentally safe.
  • Features
  • No seals or bearings to maintain.
  • High speed, foul resistant propellers or impellers, provide high shear water spraying action. No lazy sprays, bubbles, or slow boil of water.
  • One piece square flotation for stability to minimize any oscillation that can occur with round floats.
  • Watertight, removable, 100’ power cable is standard. Additional cable lengths are available in 50’ increments.
  • ETL listed (ANSI/UL508) control panel with time clock (adjustable in 15-minute increments), and Equipment Leakage Circuit Interrupter (ELCI) (US only).
  • Exclusive Franklin Electric Sand Fighter submersible motor, which implements the use of a silicon carbide mechanical sealing system.
  • 3 year Limited Warranty
  • 5HP – 11? Tall x 35? Width
  • LEAVE A MESSAGE